Things You Must know Before Freon Replacement

You can go for freon replacement in your Intellpack unit yourself. You just need a few tools, to follow the steps carefully, and to give yourself adequate time to get this process done. Most people who are trying freon replacement think that they can do it quickly because they have watched a video. You need to be a little bit more careful because refrigerant is toxic. You also do not want to do any damage to your unit doing this incorrectly. The time you invest now could save you hundreds of dollars every year.

1. Freon Is A Toxic Compound.

You can call the refrigerant anything that you like, but it is toxic. There is no way around that. The only way to protect yourself is to move slowly and wear a face mask. The simple face mask that you get at the hardware store will keep the refrigerant out of your mouth and nose. You should wear protective glasses if you do not already wear glasses, and you must make sure that you have some distance between yourself and the unit. You cannot lean into your AC unit to do this job. The freon is under pressure, and you could be injured if the pressure releases too fast while freon replacement.

It’s easy to get a freon tank from many local hardware stores, but you must make sure that you get one that is large enough for your unit. You need to know what the recommended weight of the freon is, and should learn how to read the gauges on the tank. You will have an easy time filling the tank if you have learned how to read the gauges and use the tank safely. Keep all valves on the tank closed until it is time to recharge your AC unit.

2. Where Does The Refrigerant Go While Freon Replacement?

There is a service door on your unit that you must open where you can see some simple wiring and the valve for your freon. This valve has a trigger on either side. It is closed right now because you are not adding the freon yet. There is a valve on the other side that is open because it has been released into the device.

You need to remove the service door, turn off power to your AC unit, and get your freon tank ready. You also need a wrench and pliers in case you have some extra work to do while the freon gets recharged. This process tackles several steps because you cannot simply force the freon into your unit. You must go slowly at each step so that you are safe, you do not damage the unit, and you can put everything back together without trouble.

The service door might be hard to find on some of their units. Or, you might stick it shut because the screws have rusted or corroded. Make sure that you have a heavy duty screwdriver ready to use. Someone who is not physically capable of removing the screw on their own should have a power drill with them that can remove the screw faster. You might need to get new screws if these screws are stripped. Or, you might need to clean up the service door area because it has rusted.

3. Attach Your Freon Tank When Replacing Freon.

You can attach your freon tank to the unit without opening the valve yet. You want to make sure the fittings are very tight, and you should make sure that the pressure is level on your freon tank. When you are ready to allow freon into the system, you can open the valve on your tank. You can open the valve that will let the freon start flowing into the system. You must be sure that you have a free flow of freon going into the system. And you must add only as much as it suits your unit.

Read the instructions for your Intellpack before you get started, and you will find that they are all different. This is usually a large unit, and you need to add quite a bit of freon before it is ready. However, you need to keep watch over how much freon you have added. Simply subtract from the total weight of the tank when you started. You can let the freon flow until you believe it is full, and you should turn off your tank first. Closing that valve allows time for the rest of the freon to flow into the system. You can close the valve on the near-end of the pipe, and you can remove your freon tank.

You are not all done here because there is another step that you must use to get the freon to flow in the system. Someone who stops at this point will not get the results that they want. Because they are not allowing the freon to flow in the system as it should. You must flood the system with freon, and that requires that you go back to the controls to turn on the unit.

4. Run The System After Freon Replacement Is Done.

You must turn on your system so that it will run on its highest setting. Running the system really hard for a few minutes will get the freon to flow through the system as it should. And you can turn it back down after you have run it for a bit. More people who are doing this job will not run the system on its highest setting. Because they think that is a bad thing for the system. The system will be fine for a couple of minutes. You need to be sure you have waited for the system to heat up or cool down. You can be sure that the system gets filled with freon, and you can go about your business as normal.

5. How Long Does This Process Take?

You should spend at least an hour on the freonĀ recharge process so, you can do it safely and correctly. You need to make sure that the weather outside is not bad when you try to access the unit. Do not want to be handling the freon tank when it is raining, snowing, or when it is really hot. You need some shade of it is very hot, and you do not want to get any water into the system. There are many people who will want to use the system right away once they are done. But you need to let it settle. After you have run the system on high, give it a few minutes to cool down before you go back to normal operation.

Conclusion:

There are a number of people who would like to learn how to recharge their own freon. Also, can get into your Intel pack for freon replacement and get it to flow the system again. You will find that this job takes a little bit of care so that you can put the right amount of freon in the system. You should only do this job with the power shut off on the unit. Get all your tools together, wear a facemask, and work slowly.

Write A Comment

This site uses Akismet to reduce spam. Learn how your comment data is processed.